Metal roofing
Metal Roofing in Plano, TX
Standing seam and metal shingle installations on homes, shops and outbuildings across Plano and out toward Parker and Fairview.
The Roof You Buy When You Are Done Buying Roofs
Metal roofing in Plano appeals to a particular kind of homeowner: one who has replaced an asphalt roof once already, has watched Collin County hail seasons come and go, and has decided they would rather solve the problem than repeat it. Metal handles impact, wind and heat differently from asphalt, and a properly installed standing seam system with concealed fasteners has a service life that makes the arithmetic work over a long enough horizon. Roofing Plano Texas installs both standing seam and metal shingle profiles. What we spend our time on is the detailing, because a metal roof does not fail across the panel. It fails at the ridge, the valley, the sidewall and the penetration, and those are entirely a function of how carefully it was installed.
What a Metal Roof Installation Covers
Panel, underlayment, clips, closures, valley metal, trim and labor all appear as separate lines on the estimate.
Profile and gauge selection
Standing seam or metal shingle, panel width, rib height and steel gauge chosen against your roof's pitch, exposure and how the house looks from the street. The differences are explained in plain language before you choose.
Deck preparation and inspection
The deck is exposed, inspected and repaired where needed. Metal panels telegraph an uneven deck, so this step matters more here than it does under asphalt.
High-temperature underlayment
Synthetic underlayment rated for the temperatures a metal roof reaches in a North Texas August, which is well above what a standard product is built for.
Concealed fastener installation on standing seam
Panels clipped to the deck with fasteners hidden inside the seam, so there is no exposed gasket sitting in the weather waiting to fail.
Thermal movement allowance
Metal expands and contracts through the day. Clips and fastening are detailed to let the panel move, because a panel that cannot move will oil-can, distort, or tear at its fasteners.
Ridge and hip detailing
Closures and vented ridge assemblies installed so the roof can exhaust without becoming an entry point for wind-driven rain or wildlife.
Valley fabrication
Valley metal formed and lapped correctly, with panel ends cut, hemmed and set so water stays on top of the metal where it belongs.
Sidewall and headwall flashing
Where panels meet a wall, flashing is formed and counterflashed rather than sealed. Sealant is a supplement to a correct detail, not a substitute for one.
Penetration boots rated for metal
Pipe and vent penetrations use high-temperature boots formed to the panel profile, sealed and mechanically fastened.
Trim, eave and gable finishing
Drip edge, rake trim and eave closures matched to the panel finish so the roof is complete at the edges instead of merely covered in the middle.
How a Metal Install Runs
- 01
Specification
We measure the roof, evaluate pitch and framing, and walk you through profiles, gauges and finishes with samples in hand. You will also get an honest comparison against a premium asphalt system, because metal is not the right answer for every house or every budget.
- 02
Fabrication and delivery
Panels are produced to your roof's dimensions, which minimises seams and eliminates unnecessary laps. Trim and closures come with them. Lead time is longer than asphalt and we will tell you the real number up front.
- 03
Installation
Tear-off, deck repair, underlayment, then panels from one end to the other with the detail work at each transition done as the crew reaches it. A metal install takes longer than an asphalt reroof on the same house, and the extra time is almost entirely in the details that determine whether it leaks.
Why Our Metal Work Holds Up
We will tell you if metal is the wrong call
Some roofs have too many penetrations, too complex a geometry, or a budget that metal will not serve well. We would rather say that in the driveway than take the order and have you regret it.
The details get the time they need
Ridges, valleys, sidewalls and penetrations are where metal roofs leak. We do not rush them to finish a day early, and the estimate is built with that time in it rather than trimmed to win a bid.
Everything is itemized, including trim
Panel, underlayment, clips, closures, valley metal, trim and labor appear as separate lines. Trim and closures are where cheap metal quotes hide their savings, and you should be able to see whether they are actually in there.
- Insured crews
- Written line-item estimates
- Concealed-fastener standing seam
- High-temperature underlayment
- Manufacturer-backed finish warranties
Price a Metal Roof Properly
Metal is a long-horizon decision and it deserves a real conversation rather than a brochure. We will measure, show you the profiles, and put every component on the estimate as its own line.